VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Juice  /  Vape Juice scaling from trial to bulk 2026
vape juices · B2B buyers

Vape Juice scaling from trial to bulk 2026

This page is for B2B buyers who want a working answer on specification, price and lead time before they commit a purchase order. We have written the detail down so nobody has to sit through a sales call to extract it.

Published 24 August 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Bulk packing station during the run for a B2B buyers order.
Bulk packing station during the run for a B2B buyers order.

Lead times, freight and landed cost

We work with B2B buyers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 22 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Reading a quotation properly

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

We publish a realistic band of 1.06 to 3.48 per unit for standard configurations at 240 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Where defects actually come from

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

  • Reference sample retained from every batch
  • Batch codes traceable from carton back to production date
  • Consolidated or split shipping, quoted both ways
  • Specification locked in writing before production starts
  • Artwork proof plus physical dummy for custom packaging
  • Cartons drop-tested and pallet-counted for clean freight

Building an assortment that actually turns

Sourcing trips still matter for volume buyers. Seeing the line, the ageing room and the packing station tells you in an hour what six emails cannot. We host visits by appointment and we do not stage them.

We keep a short list of approved configurations for vape juices. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

Specification summary

Typical specification for this category
Volume10 ml
Strength3 mg
Base ratio70/30 VG-PG
Flavour range24 profiles
ClosureChild resistant
BottlePET
Minimum order100 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What is the minimum order for vape juice?

Standard configurations start at 240 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 600 units because of setup time on the line.

How long does production take?

Around 22 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

Related reading

Need a quotation on vape juices?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape juices

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us