VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Juice  /  Vape Juice mould: checklist
vape juices · B2B buyers

Vape Juice mould: checklist

If you are comparing three quotes for vape juice, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

Published 14 November 2025  ·  VapeWholesaleHub  ·  Reading time 5 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.

What we test before a carton is sealed

Buyers come to us for vape juice after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for B2B buyers.

12 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

Every batch is pulled from running production, not from a display shelf. We check draw resistance, airflow balance, charge behaviour, leak performance after a temperature shift, finish quality and carton integrity, and we keep the pull records against the order number.

Labels, closures and traceability

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Transit, consolidation and timing

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Transit times move with the season. Book space early for Q4 and around Chinese New Year, when factory output pauses for two to three weeks and freight rates tighten at the same time.

  • Specification locked in writing before production starts
  • Seven-day defect reporting with replace-or-credit
  • Standing reorder schedule with a fixed cut-off
  • Consolidated or split shipping, quoted both ways
  • Artwork proof plus physical dummy for custom packaging
  • Private label files archived for future rebrands

Where the margin really sits

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

We publish a realistic band of 1.01 to 3.49 per unit for standard configurations at 60 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

Specification summary

Typical specification for this category
Volume10 ml
Strength0 mg
Base ratio50/50 PG-VG
Flavour range48 profiles
ClosureChild resistant
BottlePET
Minimum order200 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for vape juice?

Standard configurations start at 60 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 240 units because of setup time on the line.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Related reading

Need a quotation on vape juices?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape juices

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us